This didn’t always work successfully for me, but I’m not sure whether that was a problem with the installer, or something I’d done wrong! There was a worrying half-hour where I was left with an unresponsive Zen Studio and a message saying ‘Failed’, but once I’d tried a few more times, things got back on track. If I’d had a session planned, I’d have been pretty cross.Īs well as eight additional mic preamps, the Zen Studio’s rear panel houses eight line-level ins and outs on D-Subs, along with the insert points for inputs 1/2, the stereo Monitor outs, word clock and coaxial S/PDIF I/O.The launch process also checks to see whether new firmware is available, and if so, lets you install it. Also, on one occasion, a server problem meant that the update process failed, and for 12 hours or so I wasn’t able to use the Zen Studio. A good idea in principle, perhaps, and it ensures that everyone is always running the latest software, but it does mean that you need to connect to the Internet before using the Zen Studio the first time. However, double-clicking its icon in the Finder or the Windows Explorer activates not the control panel itself, but a separate ‘launcher’ application which checks to see whether a newer version is available on the Antelope web site. Gone To LaunchĪssuming you want to do more with the Zen Studio than enjoy a bonsai light show, you’ll need to turn your attention to its software control panel. The supplied transformer is rather lightweight, but does the job and has a locking connector to prevent accidents. So, for instance, the ADAT sockets are located not on the rear panel but on one end of the unit, which could be awkward if you wanted to rackmount it (for which, incidentally, you’ll need a separate rackmounting kit), and power is delivered through an external wall-wart rather than an IEC cable. The smallness of the Zen Studio also entails a few compromises in terms of physical design. However, it’s not possible to make adjustments to preamp gain using these physical controls. By default, this is configured to show bargraph meters for two rows of 16 channels, but you can use the option buttons to make it display parameters such as clock source, sample rate, preamp gain and headphone volume instead. Inbetween these and the volume control is a small but detailed colour display. In fact, the only physical controls on the Zen Studio are a power/standby button, an infinite rotary control that can be assigned to various combinations of the headphone outputs and rear-panel Monitor outs, and a pair of up/down increment buttons. So, for instance, none of the preamps has an analogue gain potentiometer or a phantom power switch. Inevitably, this marvel of miniaturisation is accomplished by the extensive use of digital control. And it doesn’t even occupy a full rack space! It also has word clock and coaxial digital I/O, plus a pair of independently addressable headphone outputs. You get 16 channels of digital I/O via ADAT sockets. There are a further eight analogue line inputs and outputs on D-Subs. It boasts 12 mic preamps on combi XLR/jack sockets. Antelope Audio’s new Zen Studio USB interface, however, raises the bar even further. If you’re happy to connect everything via MADI, you can get 64 channels in and out on one pair of connectors, while products such as RME’s Fireface 802 cram a truly comprehensive array of analogue and digital socketry into a 1U rack unit. There are quite a few audio interfaces on the market that pack a lot of I/O into a small box. If small is beautiful, then Antelope Audio’s latest product is the Mona Lisa of multi-channel audio interfaces.
0 Comments
Pioneer radio clock setup6/30/2023 Then, press and hold the “MODE” button until the display says “CLK.” Use the “TUNE” buttons to scroll through the different time zones, and then press the “MODE” button again to select the desired time zone. To set the clock on a Pioneer EEq Mosfet 50wx4, first make sure that the head unit is turned on. The clock can be set to the correct time by following a few simple steps. The Pioneer EEq Mosfet 50wx4 is a car stereo head unit that has a built-in clock. How do I set the clock on a pioneer Eeq Mosfet 50wx4? Then use the arrow buttons to select either “Auto” or “Manual”. To do this, press and hold the Clock button until the clock starts flashing. The clock can also be set automatically using the built-in timer. Then use the number buttons to set the time. To set the clock using the remote control, press and hold the Clock button until the clock starts flashing. You can also use the Menu button to access the clock settings. Then use the arrow buttons to set the time. The most common way to do it is to use the front panel of the unit. The clock on your Pioneer mosfet50wx4 can be set in a few different ways. How do I set the clock on a pioneer mosfet50wx4? Press the “OK” or “Enter” button to save the time. Use the arrow keys to navigate to the correct time.ģ. It will likely be in the bottom-left corner of the display.Ģ. Here’s how to change the clock on your radio:ġ. Your car’s radio has a clock, but it may not be set to the correct time. The following instructions will guide you through the process:Ģ) Use the “Volume +/-” buttons to select “Clock” and then press the “Enter” button.ģ) Use the “Volume +/-” buttons to select “Set” and then press the “Enter” button.Ĥ) Use the “Volume +/-” buttons to set the current time and then press the “Enter” button.ĥ) Use the “Volume +/-” buttons to select “Exit” and then press the “Enter” button. To set the clock on your Pioneer DEH 1300mp, you will need to use the menu system. How do I set the clock on my Pioneer DEH 1300mp? 6 Why does my radio controlled clock show the wrong time?.5 How do you change the time on a pioneer Mixtrax FH x700bt?.4 How do I set the clock on a pioneer Eeq Mosfet 50wx4?.3 How do I set the clock on a pioneer mosfet50wx4?.2 How do I change the clock on my radio?.1 How do I set the clock on my Pioneer DEH 1300mp?. |